Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Vanities, Tile & Fixtures in Richmond, CA: What the Job Actually Costs and Takes
A vanity, tile, and fixture package in Richmond typically runs $9,000 – $28,000, and most jobs finish in two to four weeks of on-site work once materials land. That covers tear-out, rough-in adjustments, tile setting, vanity and top installation, and hanging the fixtures. Some scopes come in lighter: a vanity-only swap with no tile work and no plumbing relocation sits in the $800 – $3,000 vanity band. Call (833) 997-7759 and we’ll walk your bathroom on site before anyone quotes a number.
What you pick inside that range is the whole story. A porcelain floor with a stock vanity and builder-grade fixtures lands near the bottom. Marble-look slab, a custom furniture vanity, and a frameless glass panel push toward the top. The structure doesn’t change; the finish level does.
How We Run a Vanities, Tile & Fixtures Job, Stage by Stage
Every phase has a decision attached to it, and we tell you which one before we start so nothing stalls mid-job.
Day 1: Site walk and demo
We protect the path, shut the water, and pull the old vanity, toilet, and floor tile. One to two days on a typical Richmond hall bath. You decide at this point whether the existing shutoff valves and supply lines stay or get replaced, and we won’t push either way. Galvanized stub-outs in a 1940s Richmond home usually get replaced while the wall is open because the alternative is tearing it open again in a year.
Days 2 – 3: Rough-in and substrate
If the vanity moves, or the shower valve relocates, plumbing and electrical rough-in happen here, followed by inspection if the scope triggers one. Then we set backer board, waterproof the wet areas, and float the floor to level. This is where you confirm tile layout and grout line width. Dense patterns cost more in labor; a straight-set 12×24 porcelain saves you real money and looks clean in a small bath.
Days 4 – 8: Tile setting
Floor first, then walls, then shower. Setting the tile takes two to three days; grouting and sealing add another. We don’t grout until thinset has cured, which is why this stage can’t be rushed. Latex-modified thinset and epoxy or cementitious grout both hold up in a steamy bathroom; the epoxy costs more and resists staining better.
Days 9 – 11: Vanity, top, and fixtures
The vanity cabinet goes in, then the countertop, then sinks, faucets, shower trim, and toilet. You’ve already picked these. Anything not on site by this stage delays the finish, which is why fixture selection happens before demo, not during. This is where the job either feels finished or feels like a list of loose ends.
Days 12 – 14: Punch, seal, and walkthrough
Caulk lines, touch-up paint, glass, and a full function test on every fixture. We walk the room with you before we call it done. If it isn’t right, we make it right, and that promise runs for 730 days under our Done Right Promise.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between
Most of the money in this job lives in three decisions. Here’s what’s honest about each.
- Vanity type. A stock cabinet with a cultured marble top starts around $800 and installs in a day. A semi-custom cabinet with a quartz or granite top climbs toward $2,500 – $3,000 and buys you real drawer hardware, soft-close doors, and a top that won’t dull. A furniture-style vanity in solid wood sits at the top of the range and adds a focal piece to a small room.
- Floor and wall tile. Porcelain is the practical pick for Richmond baths: waterproof, tough, and forgiving of a slightly uneven subfloor. Natural stone (marble, travertine) looks richer and costs more per square foot, plus it needs sealing. Glazed ceramic is the value option and shows wear sooner in a high-traffic bath.
- Fixtures. A basic chrome faucet and trim set works fine; a matte black or brushed nickel designer set with a thermostatic valve costs meaningfully more and holds its finish better. Brands like Kohler are worth the upcharge for the finish warranty; off-brand fixtures may match on looks and fall short on parts availability.
- Glass and shower trim. A framed sliding door costs less than a frameless panel. For a small Richmond bath, frameless glass reads bigger and doesn’t fight the tile.
What Vanities, Tile & Fixtures Costs in Richmond, CA
The working range is $9,000 – $28,000. Where your job lands depends on five things:
| Variable | Low end | High end |
|---|---|---|
| Vanity cabinet + top | $800 – $1,200 | $2,500 – $3,000 |
| Floor + wall tile (labor + material) | $1,800 – $3,000 | $6,000 – $9,000 |
| Fixtures (faucet, shower, toilet) | $400 – $900 | $1,800 – $3,500 |
| Plumbing/electrical relocation | $0 | $2,000 – $4,500 |
| Permit + inspection (if triggered) | $0 | $300 – $1,200 |
What pushes a job high: moving the vanity to a different wall, adding a shower where there wasn’t one, or upgrading to stone and slab. What keeps it low: same footprint, stock vanity, porcelain tile, and no change to plumbing or electrical. Our written estimate lists every line so you see where the money goes and what’s included. What it typically isn’t: unforeseen wall repair behind rotten backer board, or upgrading the vanity after demo begins. We flag those before they become change orders, and our upfront pricing means the number you see is the number you pay. Call (833) 997-7759 for a free on-site estimate.
See the difference
Before
After
Before
After
Before
AfterWhat Richmond Homes Specifically Do to This Job
Richmond’s housing stock dates mostly between 1910 and 1950, and that changes the job. The wartime duplexes near the old shipyards and along the flats in 94801 and 94804 were often built with galvanized supply lines and pier-and-post foundations. When we open a wall, we find plumbing that’s already near failure, and replacing it during a tile job is cheaper than reopening the wall later. Water service is another quirk: some duplexes share a single line between units, and adding a bathroom can trigger a requirement to separate metering. That surprises contractors new to Richmond.
Seismic work is part of the permitting conversation here. Strict Bay Area code and environmental review mean some structural or plumbing changes require a permit and inspection before we close the wall. We pull those and schedule the inspection, and we don’t hand you a homeowner permit to babysit. The marine fog and salt air matter inside the envelope too: exterior fasteners and any near-window trim corrode faster, and Richmond’s cool, wet winters expose poorly flashed areas to water intrusion. If the bathroom shares an exterior wall, we check that flashing before tiling.
We work the full range of Richmond neighborhoods, ZIPs 94802, 94807, 94808, and 94850 included, from rehabbed wartime bungalows to the duplex rows. Homeowners often pair a bathroom refresh with Specialty Roofing in Richmond when the same wall is leaking, or with Tile Roofing in Richmond if the roofline above the bath needs attention. If your project grows beyond the fixtures, our Bathroom Remodeling service is where the full scope lives, and Bathroom Remodeling in Richmond covers the parent-level picture for this market.
Serving Richmond, CA – Our Local Coverage Area
We serve Richmond and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Vanities, Tile & Fixtures in Richmond
Most Richmond bathroom fixture and tile jobs take two to four weeks of on-site work, plus a lead time for materials. Vanity and tile selection takes about a week if you haven’t picked yet; a straightforward hall bath with stock materials can finish closer to two weeks. Call (833) 997-7759 and we’ll give you a real timeline for your room.
You need a permit if plumbing or electrical lines move, or if the structural footprint changes. Cosmetic work like new tile over sound substrate or a vanity swap in the same location usually doesn’t require one. Richmond’s permit office does inspect rough-in plumbing before the wall closes, so we pull what’s owed and schedule the inspection. Call us to walk your specific scope.
Yes, and that’s the most cost-effective approach. Keeping the plumbing where it is means no rough-in, no inspection delay, and no relocation labor. A same-footprint refresh with a new vanity, porcelain tile, and updated fixtures lands in the $9,000 – $15,000 range. That usually gets you a finished, durable bath for years of use.
The full package runs $9,000 – $28,000 depending on vanity grade, tile choice, and whether plumbing moves. The number you see in the written estimate is the number you pay, provided the scope doesn’t change. We use 0% financing for 18 months and offer $1,000 off on projects over $10,000. Call (833) 997-7759 for an exact quote; estimates are free.
Every job is backed by our 730-Day Done Right Promise: if it isn’t right, we make it right for two full years. That covers labor and installation. Background-checked, uniformed technicians do the work. Call us today if something on a finished job needs a look.
Get a Free On-Site Estimate for Vanities, Tile & Fixtures in Richmond
Tell us the room, the footprint, and roughly what you want the finished bath to feel like when it’s done. We’ll set a free walkthrough, measure, look at the plumbing and substrate, and hand you a written line-item estimate with real numbers. Our technicians have up to 12 years of experience, and the 730-Day Done Right Promise is on every job in writing. Calls are answered by a live person 24/7. Call (833) 997-7759 in Richmond and get your estimate on the calendar.
Written by the team at Groundwork Construction Co.