Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Door Installation in San Francisco, CA: What the Job Actually Involves
Door installation in San Francisco runs $650 to $3,200 per door for most interior and exterior swaps, and a typical single-door install is a one-day job once the door and hardware are on site. Historic openings in Victorians and Edwardians push toward the high end because frames are rarely square, the rough opening is often an odd size, and trim has to be matched or reproduced. Call (833) 997-7759 and we’ll walk the openings with you and put the number in writing before anyone touches a hinge.
How We Run a Door Install, Start to Finish
Door installation is mostly prep. The hanging is the fast part. Here’s the real sequence we follow, and what you’ll be deciding at each stage.
Stage 1: Walkthrough and measurement (day 1, 45 – 90 minutes)
We check every opening for plumb, square and level, because in a 1900s San Francisco Victorian almost none of them are. We measure the rough opening, note the wall thickness (these old walls are often 5 to 7 inches, not the modern 4½), and photograph the existing trim and casing so a replacement profile can be matched. You decide here whether you’re keeping the existing frame or going with a full tear-out to the studs.
Stage 2: Door and hardware selection (3 – 10 days of lead time)
You pick the slab, the frame type, the finish and the hardware. This is where most schedule time disappears, not in the labor. Standard hollow-core interior slabs are usually in stock; solid-core, custom widths, and anything with a factory stain or paint finish run longer. We order once you sign off so there’s no swapping mid-job.
Stage 3: Demo and prep (2 – 4 hours per door)
The old door and casing come out, and we inspect the framing behind it. In damp-exposed wall cavities we’re looking for rot at the sill and jamb legs, which is common on exterior doors facing the fog. Rotted framing gets cut out and replaced before anything new goes in. That’s a same-day add, not a surprise later.
Stage 4: Hanging, shimming and sealing (3 – 5 hours per door)
The frame goes in, we shim and check reveal gaps on all four sides, then fasten. Exterior doors get flashing, sill pan, a bead of sealant and insulation in the frame cavity. Interior doors get the casing set and nailed. We test swing and latch before we call it done.
Stage 5: Hardware, trim and final walk (1 – 2 hours)
Knobs, locksets, deadbolts, closers, and the finish carpentry around the opening. You walk every door with us. Anything that doesn’t close, latch or seal gets fixed on the spot. Most single-door jobs are wrapped in one visit; multi-door whole-house packages run two to four days.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Choices You’ll Actually Make
Door installation in San Francisco comes down to a handful of real decisions. Here’s what each one costs you in money and in trade-offs.
- Hollow-core vs. solid-core interior slabs. Hollow-core is lighter and cheaper and fine for closets and hallways. Solid-core runs more but cuts sound dramatically, which matters in a narrow-lot Victorian where bedrooms share walls.
- Prehung vs. slab replacement. Prehung (frame and door as one unit) is the faster, more reliable install and usually the right call when the existing frame is out of square. Slab-only keeps the original casing and historic look but requires more on-site fitting.
- Wood vs. fiberglass vs. steel exterior doors. Wood matches the era but needs repainting every few years in this coastal damp. Fiberglass holds up to fog and salt air with minimal upkeep. Steel is the strongest and most secure but dents and needs touch-up.
- Finish. Factory-painted or stained doors cost more up front, but they outperform site-finish in a wet climate. Site-finish is cheaper and lets you match existing trim color exactly.
- Hardware grade. Builder-grade knobs fail fast on doors that get daily use. Upgrading to solid brass or commercial-grade levers is a small line item with a real lifespan payoff.
If the doors are part of a larger opening or trim overhaul, it’s worth looking at the wider project scope in Windows & Doors in San Francisco before you commit to a piecemeal plan.
What Door Installation Costs in San Francisco, CA
Most single-door installation in San Francisco lands between $650 and $3,200, including the door, hardware and labor. A whole-house package of eight to twelve interior doors typically runs $4,500 to $11,000.
Four things push a job from low end to high end:
- Door material and grade. A stock hollow-core slab with builder hardware sits at the bottom. Solid-core, factory-finished, or custom-width doors move the number up several hundred dollars each.
- Condition of the existing frame. Square, solid frames are easy. Rotted sills, twisted jambs, or a rough opening that has to be reframed adds hours and material.
- Exterior vs. interior. Exterior doors carry flashing, sealing, sill pans and weatherproofing, all of which add labor.
- Trim and casing. Reusing existing casing is cheaper. Reproducing period profiles on a Victorian costs more and takes longer to source.
- Permit scope. Straight swaps generally don’t trigger a permit. Enlarging an opening or changing the wall structure does, and that adds review time.
A written estimate covers the door, frame, hardware, labor, demo and haul-away, and finish carpentry. It typically does not cover structural reframing, drywall repair beyond the immediate opening, or painting. Those get called out as line items if they apply, so the number you see is the number you pay. Our Windows & Doors service covers the trim and opening work around the door as well.
See the difference
Before
After
Before
After
Before
AfterWhat San Francisco Homes Do to a Door Installation
The housing stock here writes its own rulebook. Rows of closely spaced 1880s – 1920s wood-frame Victorians and Edwardians, with unreinforced brick chimneys and soft first-story garages, dominate neighborhoods like the Mission, Noe Valley and the Haight. That means we’re usually working inside walls that have settled, shifted and been patched over a century, and door openings that were never square to begin with. We regularly see exterior door sills rotted from the bottom up after years of coastal damp, and interior doors that won’t latch because the jamb has twisted as the frame moved.
Permitting is its own reality. San Francisco’s Soft-Story and UMB retrofit ordinances mean that any work touching structure in these homes gets scrutinized, and the Planning Department’s historic-review triggers can add weeks to a job that would be a simple over-the-counter permit in a Peninsula suburb. We pull permits where they’re required and walk the inspection. The fog line at Twin Peaks even affects the schedule: on damp weeks we don’t set exterior door sealant or paint until the wood has dried. This is exactly the kind of job where a San Francisco contractor who knows the neighborhoods saves you the guesswork.
Serving San Francisco, CA – Our Local Coverage Area
We serve San Francisco and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Door Installation in San Francisco
A single door is typically a one-day job; a whole-house package of eight to twelve doors runs two to four days. The variable is lead time on the doors themselves, not the labor. Call (833) 997-7759 and we’ll give you a realistic schedule once we know the door types.
Straight door swaps usually don’t require a permit, but enlarging an opening or altering structure almost always does. In these older homes the structural question matters more than the door itself. We’ll tell you clearly which category your job falls into before work starts, and we pull the permit if one is needed.
Yes, in the vast majority of cases. Replacing a door in the existing opening doesn’t touch plumbing, and only a size change or a damaged frame calls for structural work. We confirm this at the walkthrough so there are no surprises mid-job.
Plan on $650 to $3,200 per door depending on material, frame condition and whether it’s exterior or interior. Call (833) 997-7759 for an exact quote – estimates are free and come with a design consult.
All our door installation work is covered by the 730-Day Done Right Promise. If something isn’t done right, we make it right – in writing, for two full years. Manufacturer warranties on the door and hardware apply separately on top of that.
Get a Free Door Installation Estimate in San Francisco
We’ll come out, measure every opening, check the frames for rot and square, and hand you a written line-item estimate with the door, hardware, labor and schedule spelled out. No change orders, no vague “starting at” figures. Call (833) 997-7759 – a live person answers around the clock, and the estimate and design consult are free. Homeowners often pair a door project with a Chain Link Fence in San Francisco or a Vinyl Fence in San Francisco if the yard is getting a full refresh at the same time.
Written by the team at Groundwork Construction Co.