Windows & doors
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Energy-Efficient Windows in San Francisco: What the Job Actually Involves
Energy-Efficient Windows in San Francisco typically run $5,310 to $17,700 for a replacement scope, and $9,440 to $29,500 where impact-rated glass is specified. A whole-house job on a Victorian runs three to five weeks from order to final inspection, longer if the Planning Department flags historic review. Call (833) 997-7759 for a free on-site estimate with a written, line-item number.
How we install Energy-Efficient Windows in San Francisco, stage by stage
Window work on San Francisco’s older housing stock is rarely a simple swap. The walls are thick, the framing has moved over a century, and half the openings were trimmed by hand. Here’s the sequence we actually run.
Stage 1: Measure and scope (day 1, 60 – 90 minutes)
We measure every opening, check for rot at the sill and header, and photograph the existing trim so the new units match the profile. You decide here whether we’re keeping the original interior casing or replacing it, and whether any window is going to a tempered or impact spec. That decision drives the order.
Stage 2: Order and permitting (2 – 6 weeks)
Most orders land in two to three weeks. A scope that touches the exterior wall or changes the opening size can trigger a building permit, and San Francisco permits move slower than most of the Bay Area. We pull the permit, schedule the inspection, and tell you the realistic date rather than a hopeful one.
Stage 3: Demo and prep (one to two days)
Old units come out, the rough opening gets squared, and any rot or soft framing gets cut back and replaced before anything new goes in. On a Noe Valley Victorian we often find the sill has been wet for years. That’s a repair we price before we start, not a surprise mid-job.
Stage 4: Install and seal (two to four days for a typical house)
Units go in with shims, low-expansion foam, and a proper flashing detail at the head and sill. Air sealing at the perimeter is where most of the energy performance actually comes from, so we don’t rush it. Interior trim goes back on the same day the unit sets.
Stage 5: Punch list and final inspection (one day)
We test every sash, check the weep holes drain, walk the exterior for sealant lines, and meet the inspector if the permit requires it. You get a walkthrough and the written 730-Day Done Right Promise. If a unit sticks or a seal fails in the first two years, we come back and make it right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The options you’ll choose between
Most of the cost and performance difference sits in three decisions: frame material, glass package, and whether you’re doing a full-frame or insert replacement.
- Vinyl frames: the most economical path and a good thermal performer, but the profiles are chunkier and can look wrong on a Victorian’s narrow trim. Best for rear additions and less visible elevations.
- Wood-clad (aluminum or fiberglass exterior, wood interior): the right call for historic façades where the trim profile matters. Costs more, holds paint well on the coast, and lets you match the original sightlines on the Mission and Haight rows.
- Fiberglass frames: stable in damp air, low maintenance, mid-range price. A strong compromise where salt air and fog are eating painted wood faster than you’d like.
- Glass packages: double-pane low-E with argon is the baseline for energy performance. Triple-pane adds cost and weight and rarely pays back in San Francisco’s mild climate. Where impact glazing is specified, laminated glass does double duty on safety and sound.
- Full-frame vs. insert: inserts are faster and cheaper and keep the existing frame, but they don’t fix a rotted or out-of-square frame. Full-frame is the honest choice on a 100-year-old opening that’s already failing.
We specify Therma-Tru and ViewLux where they fit the opening and the look, and we’ll tell you when a cheaper spec performs just as well.
What Energy-Efficient Windows cost in San Francisco, CA
Plan on $5,310 to $17,700 for a standard replacement scope, and $9,440 to $29,500 when impact-rated units are part of the job. Here’s what moves a project to the low or high end.
- Number and size of openings: a six-window job sits near the bottom; a full-house scope with large bays pushes to the top.
- Existing condition: rot, failed flashing, or out-of-square framing adds carpentry. This is the single most common reason a bid climbs.
- Frame and glass grade: wood-clad and triple-pane specs cost meaningfully more than vinyl double-pane.
- Full-frame vs. insert: full-frame adds demo and trim labor but fixes the opening.
- Permit and inspection scope: a structural or exterior-alteration permit adds time and fees that a simple like-for-like swap doesn’t carry.
A written estimate from us lists each opening, the unit spec, labor, disposal, permit fees, and any repair allowance. It doesn’t include unforeseen structural repair, which we price separately once we open the wall and show you the photos. The number you see is the number you pay on the scope we agreed.
See the difference
Before
After
Before
After
Before
AfterWhat San Francisco homes specifically do to this job
San Francisco is a pre-1906 wood-frame city. Rows of 1880s – 1920s Victorians and Edwardians sit shoulder-to-shoulder on narrow lots, and most of the openings we work on were cut by hand a century ago. That means the rough opening is rarely square, the original casing is worth saving, and the window has been moving with the house for a long time. It also means the city’s Soft-Story and UMB retrofit rules hover over anything that touches the exterior wall, and the Planning Department’s historic-review triggers can add weeks to a job that would be a simple permit in Daly City or South San Francisco. Coastal fog and damp winters are the other factor: constant moisture drives rot in sills and headers, so we inspect and price repair before we order, not after. In Noe Valley and the Mission we regularly find sills that have been wet for years and only show up once the unit comes out. Homeowners often pair this with Fence Repair in San Francisco while we’re already on site, or with Iron Fence in San Francisco if the exterior work is part of a larger scope. This is also a natural time to look at the wider project as part of a full Windows & Doors in San Francisco plan. We cover all of San Francisco.
Serving San Francisco, CA – Our Local Coverage Area
We serve San Francisco and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked – Energy-Efficient Windows in San Francisco
A typical house takes three to five weeks from order to final inspection, with two to four days of actual install once units arrive. Permit turnaround and historic review are the usual variables. Call (833) 997-7759 for a date estimate on your address.
Like-for-like replacement often doesn’t require a building permit, but any change to the opening size, exterior wall, or historic façade can trigger one. We determine that during the site visit and pull the permit if it applies. Call (833) 997-7759 to find out where your scope lands.
Standard replacement runs $5,310 to $17,700, and impact-rated scopes run $9,440 to $29,500. Frame material, glass package, and existing rot drive the difference. Call (833) 997-7759 for an exact quote, and estimates are free.
Insert replacements keep the existing frame and trim, so interior disturbance is minimal. Full-frame replacement opens the wall and requires trim work. We’ll tell you which one your openings actually allow. Call (833) 997-7759 to schedule the assessment.
Workmanship is covered by our 730-Day Done Right Promise, and the unit manufacturer’s warranty covers the glass and frame. If a seal fails or a sash sticks within that window, we come back and fix it. Questions? Call (833) 997-7759.
Get a free estimate on Energy-Efficient Windows in San Francisco
Call (833) 997-7759 to schedule a free on-site estimate for Energy-Efficient Windows in San Francisco. We’ll measure each opening, inspect for rot, and walk you through the spec choices. You get a written, line-item quote and a realistic timeline, backed by our 730-Day Done Right Promise. A live person answers around the clock.
Written by the team at Groundwork Construction Co.