Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Aluminum Fence in San Francisco, CA: What It Runs and How Long It Takes
A new aluminum fence in San Francisco typically costs between $4,720 and $11,800, and most residential runs are finished in two to four working days once the materials land and weather cooperates. That figure covers a standard 4- to 5-foot ornamental run with posts set on a proper footing, not a decorative panel kit. The number moves with height, grade, gate count and how hard your ground is to dig. Call (833) 997-7759 for a free on-site estimate.
How an aluminum fence actually gets built here, step by step
Aluminum fencing looks simple and the installation has a rhythm to it, but the sequence matters. Skip a stage and the fence leans, sags, or pulls out of the ground in a wet San Francisco winter. Here’s the order we follow.
Stage 1: Site walk and layout (day one, 1 – 2 hours). We walk the property line with you, mark post locations, and confirm the run against your plat or survey if you have one. This is where you decide the height, the panel style, and where the gate or gates land. If a gate swings toward a shared driveway or a neighbor’s wall, we flag it now, not after the posts are in.
Stage 2: Locating utilities and pulling the permit (day one to week two, depending on scope). Before a shovel goes in, we call 811 to mark gas, electric, water and sewer. In San Francisco, a fence under 6 feet on a single-family lot often doesn’t require a building permit, but anything taller, on a heritage property, or in a planned-unit development may trigger review. We pull what’s required rather than gamble. This stage is the single biggest variable in your timeline.
Stage 3: Demolition and excavation (day two, 4 – 8 hours). Old fencing, roots, and hardscape come out. Post holes get dug to depth, typically 24 to 36 inches in our soil, deeper on sloped lots where frost isn’t the issue but wind load and soft fill are. On a hillside Noe Valley or Bernal Heights lot, this is where the day goes long.
Stage 4: Posts, concrete and curing (day two and three). Posts set in concrete need to cure before you hang panels on them. We set them plumb, brace them, and let them sit. You’ll get a day of quiet while the concrete does its work. Rushing this is how fences end up crooked by spring.
Stage 5: Panels, gates and hardware (day three to four). Rails and pickets go up, gates get hung with hinges and a latch, and we walk the line with you. Final inspection and cleanup close it out. Total elapsed time is usually two to four working days on the ground, plus permit and lead-time.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The aluminum fence choices you’ll actually be deciding between
Aluminum fencing isn’t one product. The pick between these options drives both the look and the price:
- Residential-grade vs. heavy commercial grade. Residential aluminum is lighter and cheaper, fine for a backyard run. Commercial-grade has thicker walls and heavier posts, and it’s the right call facing a street or a windy exposure.
- Rackable vs. fixed panels. Rackable panels follow a slope, so the top rail stays parallel to the ground on a hill. Fixed panels step down in sections. San Francisco lots are rarely flat, so this one matters.
- Powder-coat finish and color. Standard black, bronze and white are the common picks. A quality powder coat holds color and resists chipping far better than a painted finish; the trade-off is cost and a limited color menu.
- Picket spacing and style. Ornamental styles with decorative finials and scrollwork cost more and read as iron; a plain flat-top run is the value option.
- Gate configuration. A single walk gate is the baseline. A double drive gate, a self-closing hinge, or an automatic opener adds real money and needs heavier posts and a proper footing.
- Post caps and accents. Small line item, big visual difference. Worth pricing in while the order is open.
Aluminum fits the fog-belt climate well. It won’t rust, rot or need repainting the way a wood run does, and it shrugs off the damp that eats untreated lumber. If your surrounding project is wood, though, we’ll tell you plainly, because a wood fence at a lower entry price is sometimes the honest answer.
What an aluminum fence costs in San Francisco, CA
For a typical residential property, aluminum fence installation in San Francisco runs $4,720 to $11,800. Here’s where that spread comes from:
- Linear footage. A 100-foot backyard perimeter sits near the low end. A 200-foot run around a corner lot pushes toward the top.
- Height and grade. A 4-foot residential run is the budget line. A 6-foot commercial-grade run with heavier posts is the high line.
- Gates. Every gate adds hardware, a heavier post, and a footing. A drive gate with an opener is the single biggest line-item jump.
- Terrain and demolition. Removing an old fence, cutting roots, or digging into a slope adds labor hours you’ll see on the estimate.
- Permit and design review. Required permits, historic review on a period home, and HOA submittals add time and cost outside the fence itself.
A written line-item estimate from us shows the footage, the grade, the gate count, footing depth and the permit line. It also states what’s not included: landscaping repair, irrigation line relocation, or a neighbor’s shared-fence cost split. Upfront pricing means the number we quote is the number you pay, and the work is covered by our 730-Day Done Right Promise. If your project is part of a full Fence Installation in San Francisco, we’ll price the whole run together rather than piecemeal.
See the difference
Before
After
Before
After
Before
AfterWhat San Francisco homes specifically do to this job
Working on fence lines in this city is a different animal from a Peninsula suburb. The housing stock is the reason. San Francisco’s core is packed with 1880s to 1920s wood-frame Victorians and Edwardians on narrow, shoulder-to-shoulder lots, many with a soft first-story garage and an unreinforced brick chimney. Set a fence against that reality and the questions multiply: where exactly does the property line sit when two buildings share a wall, is the neighbor’s structure dependent on the old fence line, does a post hole undercut a footing?
Permitting adds its own layer. Historic review can be triggered on a period façade, and HOA or planned-unit rules apply in some blocks. The fog-cooled damp means exposed wood framing rots fast, which is one reason aluminum is a practical choice where the old run sat in constant moisture. In the Mission, Noe Valley and the Haight, we routinely see the same failure: a wood run that has been patched for decades finally gives up at the posts, and the homeowner wants a material that won’t repeat the cycle. Winter rain rotates the schedule, so a dry-weather install window is worth planning around.
We cover the full city, including ZIPs 94142, 94144 and 94145, and you can see the wider coverage on our San Francisco service-area page. Homeowners often pair a new fence with Driveway Repair & Replacement in San Francisco when the old fence line meets the driveway apron, or with Patios, Walkways & Pool Decks in San Francisco when the yard is being redone at the same time. If you’re still weighing the broader scope, our Fence Installation service covers the full range of options, and our team can walk you through the trade-offs.
Serving San Francisco, CA – Our Local Coverage Area
We serve San Francisco and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked: Aluminum Fence in San Francisco, CA
Most aluminum fence installs take two to four working days on site once materials arrive and the permit clears. Permit review and material lead time can add one to three weeks on top. Call (833) 997-7759 and we’ll give you a realistic timeline for your lot.
Not always. A fence under 6 feet on a single-family lot often skips the building permit, but height, historic-home status and HOA rules can require review. We pull what’s required and pass the inspection, and we’ll tell you upfront whether yours needs one.
Yes, in most cases. We call 811 to mark utilities before digging and design the post layout around them. If a line sits exactly where a post needs to go, we shift the post rather than relocate the line, which keeps cost down.
Expect $4,720 to $11,800 for most residential runs, depending on footage, height, grade and gate count. Call (833) 997-7759 for an exact quote – estimates are free and itemized.
Every install is covered by our 730-Day Done Right Promise. If something isn’t right, we make it right. Our technicians bring up to 12 years of experience, and we stand behind the finished fence in writing.
Get a free on-site estimate for your aluminum fence
Call (833) 997-7759 to schedule a free on-site estimate for aluminum fence in San Francisco. A live person answers around the clock, so no voicemail. We walk the property line, measure the run, talk through grade and gates, and hand you a written line-item quote with the permit scope spelled out. No pressure and no surprises, and projects over $10,000 qualify for $1,000 off with 0% financing for 18 months.
Written by the team at Groundwork Construction Co.