Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in Burlingame, CA: What It Costs and What the Job Actually Involves
A wrought iron fence in Burlingame typically runs $3,500 to $9,000 for a residential front or side-yard run, and most installs take two to four working days once the fence is fabricated. The number that matters most here is salt. Burlingame sits between the bay and the coastal hills, and the damp, fog-heavy air corrodes steel fasteners, hinges, and weld points years before inland customers ever see it. Call (833) 997-7759 for a free on-site estimate.
Day by Day: How We Build an Iron Fence Here
Iron work is unforgiving of shortcuts. A fence that starts corroding at the base in four years was almost always set wrong on day one. Here’s the sequence we run.
Stage 1 – Site walk and layout (about 1 to 2 hours, day 1). We mark the property line, check for buried irrigation, low-voltage lighting, and gas or electrical runs before anyone digs. On Burlingame’s narrower lots, the set-back line between you and your neighbor is often ambiguous, so this is where you decide the exact run and gate swing. A survey is worth having if the line is contested.
Stage 2 – Footings and posts (day 1 into day 2). We dig post holes to depth, pour concrete footings, and set the posts plumb with proper drainage at the base of each one. Water pooling around a post is what kills iron fences on the Peninsula; we set footings so water sheds away and cap the post tops. Concrete needs about 24 hours to cure before we load the fence, so this is the quiet day.
Stage 3 – Fabrication and dry fit (day 2). Panels, rails, and pickets get laid out and checked against the actual site. Slopes are common on Burlingame’s older lots, and a racked panel on a grade looks wrong fast. You confirm picket spacing, height, and finish color at the dry-fit, before anything is permanently fastened.
Stage 4 – Installation (day 3). Panels go up, gates are hung and adjusted, and every fastener gets torqued. This is also where we confirm the gate hardware is stainless – hinges and latches are the first things to seize in coastal air.
Stage 5 – Finish coat, touch-up, and walkthrough (day 3 into day 4). We touch up weld points and any scratches from installation, check the gate swing, and walk the run with you. Anything that needs attention gets noted and handled before we call the job done.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Cast Iron, Wrought Iron, or Steel: The Honest Trade-Offs
What gets sold as “iron” today is usually one of three things. Each has a real place, and the choice drives both cost and how long the fence holds up in Burlingame’s damp air.
- True wrought iron: the traditional option, hand-forged and heavy. It suits period homes well, but it’s the most expensive per linear foot and needs re-painting every few years to stay ahead of rust. Best for historically sensitive properties.
- Cast iron: heavier and more ornate, with decorative castings. Beautiful on a Craftsman or Spanish Colonial Revival facade, but brittle if struck and costly to repair. Suits a formal front yard, less so a busy driveway edge.
- Powder-coated steel or aluminum: the practical choice for most Burlingame lots. Lighter, lower cost, and the factory finish resists corrosion far better than site-painted iron. Aluminum won’t rust at all; steel with a good powder coat holds up well if the fasteners are also protected. Specify stainless or coated hardware either way.
Finish matters as much as metal. A galvanized or zinc-rich primer under the topcoat is what keeps salt air from finding bare steel. Spec it in writing. Nylon or stainless rollers and gate hardware are worth the small upgrade.
What an Iron Fence Costs in Burlingame, CA
Expect $3,500 to $9,000 for a typical residential iron fence in Burlingame. A short side-yard run lands near the bottom; a full front perimeter with a driveway gate and decorative panels pushes to the top and beyond. Here’s what moves the number:
- Linear footage and height: the single biggest factor. A 40-foot run at 4 feet tall is a very different job from 120 feet at 6 feet.
- Material grade: powder-coated aluminum sits at the low end, true wrought iron at the high end, with steel in between.
- Gates: a standard walk gate is one price; a wide driveway gate with proper posts and hardware is another.
- Site conditions: slopes, rock, tree roots, and tight access all add labor. Burlingame’s narrow lots and mature landscaping often mean hand-digging near the property line.
- Permits: fences over a certain height or near a corner may need a permit and a survey; that gets quoted separately and pulled before we dig.
A written estimate itemizes posts, panels, gates, hardware, finish, and permit fees. It won’t include a survey if one turns out to be needed, or repairs to a damaged existing retaining wall the fence would sit on. We price it so the number you see is the number you pay.
See the difference
Before
After
Before
After
Before
AfterWhy Burlingame’s Old Lots Change This Job
Burlingame is one of the oldest and most architecturally protected suburbs on the Peninsula, and much of the housing stock in Burlingame Park, Downtown, and Easton Addition dates to the early 1900s through the 1940s – Craftsman bungalows, Spanish Colonial Revival, and Tudor cottages. That history shows up in fence work. Property lines on these narrow lots are often a few inches off from where a homeowner assumes, original surveyed corners are missing, and a new iron fence that respects the neighboring setback can need a survey before we set a single post. The historic-preservation scrutiny that governs additions and second stories rarely applies to a fence outright, but a period-appropriate design reads better on Easton Addition and Burlingame Park homes and is worth planning for. This is part of the wider scope we cover under Fence Installation in Burlingame, and the coastal failure pattern is real: we routinely see gate hinges seizing and post bases rusting within four to six years on fences set without stainless hardware and drainage.
The climate does the rest. Cool, fog-influenced summers and damp winters mean persistent morning moisture on metal. Proper footings that shed water, capped posts, stainless hardware, and a galvanized primer are what buy the extra years.
Serving Burlingame, CA – Our Local Coverage Area
We serve Burlingame and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Iron Fence in Burlingame
Most residential iron fence installs in Burlingame take two to four working days on site, plus a lead time for fabrication if the panels are custom. Simple runs on flat ground move fast; slopes, gates, and permitting add days. Call (833) 997-7759 to get a timeline for your specific run.
Often yes, depending on height, location, and proximity to a corner or the property line, and a survey may be required to confirm the line. We pull the permits and handle the inspection as part of the written estimate – it’s not left to you to sort out. Call (833) 997-7759 to confirm what your lot needs.
Plan on $3,500 to $9,000 for a typical residential iron fence in Burlingame. Length, height, material grade, gate count, and site conditions drive the number. Call (833) 997-7759 for an exact quote – estimates are free.
It can, but proper hardware and finish prevent most of it. Aluminum won’t rust; steel and iron need a galvanized primer, a good topcoat, and stainless fasteners to hold up in Burlingame’s damp, fog-influenced climate. We spec it that way on every job. Call (833) 997-7759 to talk through the finish options.
Every install is covered by our 730-Day Done Right Promise – if it’s not done right, we make it right. That’s one of the longest workmanship guarantees in residential construction. Call (833) 997-7759 if you have questions about coverage.
Get a Free Iron Fence Estimate in Burlingame
Call (833) 997-7759 for a free on-site estimate on your iron fence in Burlingame. A live person answers 24/7, and we’ll walk the property line with you, talk through material and finish, and hand you a written line-item quote – posts, panels, gates, hardware, finish, and permits spelled out. No change orders, no surprises. If you’re also refreshing the hardscape, homeowners often pair this with Patios, Walkways & Pool Decks in Burlingame, and larger lot plans sometimes fold in ADU Design & Permitting in Burlingame. Our fence installation service covers the full range, and we work across Burlingame.
Written by the team at Groundwork Construction Co.