Driveway & pavers
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Paver Driveways in Foster City, CA: What the Job Actually Involves
A paver driveway in Foster City runs $7,000 – $18,000 for most single-family homes, and a typical install takes 3 to 5 working days from demolition to the final sweep of joint sand. The job means removing the old slab or asphalt, rebuilding a compacted base designed for our bayfront soils, then laying interlocking pavers on a proper edge restraint. Call (833) 997-7759 for a free on-site estimate with a written, line-item quote.
How We Build a Paver Driveway, Stage by Stage
Paver work is mostly base work. The visible layer is the last 20% of the job, and it’s the part that fails first when someone skips steps. Here’s the actual sequence we run on a Foster City driveway.
Stage 1: Site visit and layout (day 1)
We measure the apron, check the slope away from the garage, and confirm where the city right-of-way ends and your property begins. You decide the paver style and color at this point, because the base thickness and edge detail depend on it.
Stage 2: Demolition and haul-off (day 1 – 2)
The old concrete or asphalt comes out with a mini excavator, and the debris leaves the same day. On Foster City lots, this is also when we find out what’s under the slab: old sprinkler lines, a buried cleanout, or the root system of a ficus that has been lifting the old surface for years.
Stage 3: Excavation and base prep (day 2 – 3)
We excavate 8 to 12 inches deep, then build up in lifts of 3 to 4 inches of compacted Class II aggregate base, wetting and plate-compacting each lift. This is the stage that matters most in Foster City, where the ground is engineered fill and the water table sits close to the surface. You’ll see us checking grade with a laser level, not eyeballing it.
Stage 4: Setting bed and paver installation (day 3 – 4)
One inch of washed concrete sand goes down, screeded flat, then the pavers go in a running bond or herringbone pattern. Edge restraints get anchored into the base every 12 inches, and cuts at the garage apron and sidewalk are made wet with a masonry saw for clean lines.
Stage 5: Compaction, sand, and cleanup (day 4 – 5)
A plate compactor runs over the finished field, polymeric joint sand fills the gaps, and we water it in. You get a walkthrough, a sweep, and the driveway is ready for foot traffic that evening and vehicle traffic in 24 hours. Total: 3 to 5 days for most Foster City driveways, longer if the base turns out to be wet or unstable.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between
Most of the decisions happen before we break ground. Here’s what’s on the table and what each choice actually costs you in money, maintenance, or longevity.
- Concrete pavers (the standard choice). Interlocking units in troweled or tumbled finishes, typically 60mm thick for driveways. Cost lands in the middle of the $7,000 – $18,000 range. They handle freeze-thaw and root heave better than poured concrete because individual units can shift without cracking.
- Clay brick pavers. Warmer color, longer lifespan, but higher cost and fewer pattern options locally. Best for homeowners who plan to stay 15+ years and want the driveway to look like it belongs with the house.
- Permeable pavers. Open-graded units with wider joints and a stone reservoir underneath. They cost 15 – 25% more than standard pavers and require more base excavation, but they manage stormwater on site, which matters in a city with strict bayfront drainage requirements.
- Belgard and similar brand systems. We work with Belgard and other verified paver lines so you can see physical samples, not catalog photos. Color matching across production runs is real, and we order the full quantity at once to keep dye lots consistent.
- Pattern and border. A running bond is fastest and cheapest. Herringbone or a soldier-course border adds labor and 5 – 10% to the cost, but it also adds visual structure to a wide driveway.
What Paver Driveways Cost in Foster City, CA
The range for a full paver driveway install in Foster City is $7,000 – $18,000. That’s for a standard two-car driveway of roughly 400 to 700 square feet with demolition, base, pavers, and joint sand included. The variables that move the number:
- Square footage. Each additional 100 square feet lands around $1,200 – $2,200 depending on the paver selected.
- Existing surface condition. A cracked slab with root intrusion underneath costs more to remove and repair than clean asphalt.
- Base depth. Foster City’s engineered fill sometimes needs extra excavation and aggregate to reach a stable subgrade. That’s a real line item, not a surprise.
- Paver grade and pattern. Permeable systems and clay brick sit at the high end. Standard concrete pavers in running bond sit at the low end.
- Drainage and slope. If the driveway needs a channel drain or a regraded apron to move water away from the garage, expect $800 – $2,000 more.
Your written estimate will list demolition, haul-off, base, pavers, edge restraints, joint sand, and cleanup line by line. It won’t include landscape repair beyond the driveway edges, new gutters, or replacing a damaged garage apron slab. If you’re also reworking the front yard, this is often part of a full Driveway & Pavers in Foster City scope.
See the difference
Before
After
Before
After
Before
AfterWhat Foster City Homes Specifically Do to This Job
Foster City isn’t standard suburban ground. The city is an engineered island built on imported fill, ringed by levees and lagoons, with a high water table and liquefaction-prone soils underneath. A paver driveway here needs a base designed for that reality, not a cookie-cutter 4-inch slab of aggregate. We see it in the field: driveways that settle unevenly on the lagoon side, edge restraints that pull loose after a wet winter, and joint sand that washes out when king tides push groundwater up through the soil.
Salt-laden onshore air is the other factor. It corrodes fasteners and metal edging noticeably faster on the bay side. We spec galvanized or stainless edge restraints and polymeric sand that resists moisture. Most homes we work on here went up during the 1960s – 1980s master-planned build-out on slab-on-grade foundations, so old irrigation lines and aging utility runs under the driveway are common. Pulling a permit and confirming the layout before demolition saves a lot of expensive surprises. For a driveway in the 94404 ZIP on a typical lot, we’re usually working within a 3 – 5 day window once the base is confirmed stable. If your project grows into a new structure on the property, homeowners often pair this with Garage Conversion ADU in Foster City or an ADU Design & Permitting in Foster City project we also handle.
We cover the whole city on our Foster City service page, and our broader Driveway & Pavers service covers the full range of hardscape work.
Serving Foster City, CA – Our Local Coverage Area
We serve Foster City and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Paver Driveways in Foster City
A typical paver driveway takes 3 to 5 working days, from demolition to the final compaction and joint sand. Permitting adds 1 to 2 weeks if the driveway touches the public right-of-way or changes drainage. Call (833) 997-7759 to schedule a free on-site estimate and get a real timeline for your address.
Yes, in most cases. Any change to the driveway apron at the sidewalk, drainage pattern, or right-of-way requires a permit, and bayfront flood-plain properties may need additional review. We pull the permits and handle the inspections as part of the job. Call (833) 997-7759 and we’ll walk you through what your specific property needs.
No, we don’t recommend it, and we won’t do it. A thin paver layer over cracked or settling concrete fails within a couple of seasons, especially on Foster City’s fill soils. The base is the whole point. We demolish the old surface, rebuild the base, and lay pavers on a proper foundation. Call (833) 997-7759 for a free estimate that covers the full removal and rebuild.
Most paver driveways in Foster City run $7,000 – $18,000, depending on square footage, paver choice, base depth, and drainage work. Permeable systems and clay brick sit at the high end; standard concrete pavers in running bond sit at the low end. Call (833) 997-7759 for an exact quote, with upfront pricing and no surprises.
Every paver driveway we install is covered by our 730-Day Done Right Promise. If the base settles or a section heaves, we come back and fix it. Paver manufacturers also carry their own product warranties, which we review with you at the estimate. Call (833) 997-7759 to schedule your free estimate.
Get a Free Paver Driveway Estimate in Foster City
We’ll come out to your Foster City property, measure the driveway, check the slope and base condition, and walk you through paver options with physical samples. You’ll leave the visit with a written, line-item estimate and a clear timeline. No pressure, no vague bids, no surprise change orders. Call (833) 997-7759 to schedule your free estimate, and a live person will pick up, any day of the week.
Written by the team at Groundwork Construction Co.