Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in San Francisco: What It Costs and How Long It Takes
A wrought iron fence in San Francisco typically runs $4,130 to $10,620, installed, depending on linear footage, height, and whether you’re setting posts into a hillside or a flat lot. Most residential jobs take three to five working days once permits clear, and historic-district review can add weeks before that clock even starts. Call (833) 997-7759 for a free on-site estimate and a written, line-item quote before any work begins.
How We Build an Iron Fence in San Francisco, Start to Finish
Iron work is unforgiving of shortcuts. Posts set shallow or railings anchored into crumbling stucco will fail within a season, and in this city’s damp air you’ll see the rust before you see the sag. Here’s the actual sequence, so you know what’s happening on your property and when we need a decision from you.
Stage 1: Site walk and layout (day 1, about 90 minutes)
We measure the run, check property lines against your survey, and probe what’s underground along the fence path. On a Noe Valley or Mission lot that often means finding old clay drain tile, irrigation lines, or a brick footing from a fence that stood there in 1920. You decide the gate locations and swing direction at this stage, because moving a gate later means new posts.
Stage 2: Demo and footing prep (days 1 – 2)
Out comes the old fence, and we set new footings at the spacing your panel design requires, usually 6 to 8 feet on center. Footings go below the frost line and, on sloped lots, get stepped so the fence follows grade without a floating rail at the bottom. On tight San Francisco side yards, this is often hand-dig work because equipment won’t fit past the building.
Stage 3: Fabrication and delivery (days 2 – 6, off-site)
Welded steel panels and pickets are cut and finished to your spec, then hot-dip galvanized or powder-coated. This is the part that runs in parallel with footing cure, and it’s where your finish choice has the biggest long-term consequence. You approve the final panel drawing before anything gets welded.
Stage 4: Setting and assembly (days 3 – 4)
Posts set into cured footings, panels hung plumb, gates aligned and hardware mounted. We check every gate for smooth swing and latch engagement before we call it done. On a shared property line, this is also when we confirm nothing encroaches on your neighbor’s side.
Stage 5: Finishing and walkthrough (day 5)
Touch-up on any scratched coating, final cleanup, and a walkthrough with you. We hand over care instructions and confirm the finish warranty terms in writing. Most jobs are finished in a single visit cycle after fabrication; larger runs with multiple gates may stretch a day or two.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Iron Fence Options You’ll Choose Between
Every iron fence decision comes down to a handful of trade-offs. Here’s what actually matters and how each choice holds up.
- Mild steel vs. wrought iron: True wrought iron is largely a salvage material now; most residential work uses mild steel. It’s stronger per pound and easier to fabricate, but it rusts fast if the coating fails. Wrought iron, when you can source it, resists corrosion better and lasts longer, at a higher price.
- Hot-dip galvanized vs. powder-coat finish: Galvanizing gives the best corrosion protection and is the right call for coastal fog exposure. Powder coat gives a cleaner, more uniform black and better color options but chips at weld points. The two are often combined.
- Picket spacing: Tighter spacing (under 4 inches) improves security and keeps small pets in; wider spacing costs less per foot and reads more open. Most San Francisco front-yard fences land at 4-inch spacing.
- Height: 36 to 48 inches is the residential sweet spot. Anything over 6 feet in a front yard needs a permit and often triggers planning review.
- Gate hardware: Self-closing hinges, keyed latches, and a concealed closer add cost but make a driveway or pedestrian gate usable daily without sagging.
What an Iron Fence Costs in San Francisco, CA
Residential iron fence installation in San Francisco falls between $4,130 and $10,620. That range covers a typical front-yard run with one gate on a flat or mildly sloped lot. Several things push a job toward the high end.
- Linear footage and height: A 60-foot fence at 4 feet sits near the low end; 100-plus feet at 5 feet with multiple gates climbs toward the top.
- Site access and slope: Hillside lots, narrow side yards, and rear-yard runs that require hand-digging add labor hours.
- Existing conditions: Removing an old masonry or brick footing costs more than pulling wood posts.
- Finish grade: Galvanized-plus-powder-coat finishes and custom cast finials push material cost up.
- Permit scope: Historic-district review or a height variance adds both time and fees.
A written estimate from us itemizes panels, posts, footings, gates, hardware, finish, and permit fees. It does not include landscape repair beyond reseeding, or relocation of utilities discovered underground after the walkthrough. Upfront pricing means the number in the quote is the number you pay unless you change the scope.
See the difference
Before
After
Before
After
Before
AfterWhat San Francisco Homes Specifically Do to This Job
This city’s housing stock makes an iron fence job harder than it looks on paper. Rows of 1880s – 1920s wood-frame Victorians and Edwardians sit shoulder-to-shoulder on narrow lots across the Mission, Noe Valley, and the Haight. That means shared property lines, tight side access, and footings that often hit old brick or unreinforced concrete from an earlier fence. The city’s Soft-Story and UMB retrofit ordinances mean many of these homes have had foundation and first-story work done, so we check that a new fence footing won’t interfere with existing bolting or bracing. Historic review triggers in some districts can add weeks to a job that would be a simple permit in Daly City or South San Francisco. And the fog line at Twin Peaks genuinely decides whether concrete cures that week, so our schedule rotates around the damp, fog-cooled winters rather than heat. If you’re planning a broader exterior project, homeowners often pair this with Patios, Walkways & Pool Decks in San Francisco or a full Fence Installation in San Francisco scope.
We bring our Fence Installation service across San Francisco and the ZIP codes 94142, 94144, 94145, and 94146, and we coordinate closely with homeowners planning a ADU Design & Permitting in San Francisco project where fence lines and property setbacks need to be worked out together.
Serving San Francisco, CA – Our Local Coverage Area
We serve San Francisco and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Iron Fence in San Francisco
Most residential iron fence jobs take three to five working days on site once permits clear, with fabrication running in parallel off-site. Historic-district review or a height variance can add several weeks before work begins. Call (833) 997-7759 to get a realistic timeline for your address.
Front-yard fences and any fence over 6 feet in height generally require a permit, and properties in historic districts may trigger additional planning review. We pull the permits and handle inspection coordination as part of the job. Call (833) 997-7759 and we’ll tell you exactly what your address needs.
Yes in most cases. We design footings to avoid existing foundations, seismic retrofit hardware, and buried utilities, which is a common concern on San Francisco’s older Victorians and Edwardians. If a conflict is found during the walkthrough, we flag it before any digging starts.
Expect $4,130 to $10,620 for a typical residential run with one gate. Linear footage, slope, finish grade, and permit scope move the number most. Call (833) 997-7759 for an exact quote – estimates are free.
Every iron fence we install is covered by our 730-Day Done Right Promise. If workmanship fails within that window, we make it right, and the finish manufacturer warranty terms are handed to you in writing at the walkthrough.
Get a Free Iron Fence Estimate in San Francisco
Call (833) 997-7759 for a free on-site estimate on your iron fence. A live person answers around the clock, and we’ll walk your property, measure the run, check for permit triggers, and hand you a written, line-item quote with no surprises. Financing at 0% for 18 months is available, and projects over $10,000 get $1,000 off.
Written by the team at Groundwork Construction Co.