Roofing
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Metal Roofing in Burlingame: What the Job Really Involves
Metal roofing in Burlingame typically runs $15,000 to $40,000 installed, takes seven to fourteen working days on a standard house once materials land, and starts with a tear-off down to the decking so we can see what years of fog and morning damp have done to the roof structure underneath. On the older homes around Easton Addition and Burlingame Park, that first look often changes the plan. Call (833) 997-7759 and we’ll schedule a free on-site estimate.
How a Metal Roof Goes On, Stage by Stage
A metal roof is a sequence problem more than a materials problem. Get one stage wrong and the panels above it will remind you for thirty years. Here’s how we run it.
Stage 1: Tear-off and deck inspection (one to three days)
We strip the old roofing to the bare sheathing and walk every square foot. On Burlingame’s 1910s to 1940s stock, this is where we find the soft spots: old skip sheathing, dry-rotted fascia, failed step flashings at wall intersections. You decide whether we replace individual sheets or re-sheet the whole deck. That decision is the single biggest swing in the final number.
Stage 2: Deck repair and underlayment (one to two days)
Bad sheathing gets cut out and replaced. Then we install a high-temperature synthetic underlayment across the full roof, not just the valleys and penetrations. Burlingame’s damp winters and the moisture that lingers on north slopes until 10am make a full underlayment layer worth every dollar; it’s the backup barrier for the twenty or thirty years before anyone sees the deck again.
Stage 3: Flashing and trim (one to two days)
Valley metal, step flashing, counter-flashing at chimneys, drip edge. This is the stage where Burlingame’s climate punishes shortcuts: fog-driven moisture works sideways into wall assemblies, so every penetration gets layered flashing, not a bead of caulk. You’ll choose your trim color and profile here.
Stage 4: Panel installation (two to five days)
Panels go up in runs, fastened on the correct schedule per the manufacturer’s spec so the warranty stays valid. Standing seam panels are concealed-fastened, which matters in salt-influenced air because there are no exposed screw heads to corrode. You confirm panel profile, panel width, and whether you want a vented ridge.
Stage 5: Final inspection and cleanup (half a day)
We walk the roof, check every fastener row and penetration, sweep the gutters, and run a magnet over the yard and driveway for stray screws. Then the manufacturer’s warranty registration gets filed and you get the paperwork for a local building inspection.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Actually Choose Between
Metal roofing is a category, not a single product. What you pick changes both the price and how the roof behaves in Burlingame’s fog belt.
- Standing seam (the premium pick): Concealed fasteners, long panel runs, cleanest look on a low-slope or Craftsman roofline. Highest cost per square, but the least hardware exposed to coastal moisture. Best for homeowners who plan to stay twenty-plus years.
- Exposed-fastener panels: Lower cost, faster install, and a familiar look on outbuildings and simple gable roofs. Honest trade-off: every screw head is a potential leak point, and in salt-influenced air those washers degrade faster than inland. We only recommend them where the budget genuinely dictates.
- Stone-coated steel: Steel panels coated in stone granules that mimic tile or shake. A strong fit for Spanish Colonial Revival and Tudor cottages where you want the original look without the weight of real tile. Costs less than standing seam in most cases.
- Aluminum panels: The corrosion champion for near-coast homes. Lighter than steel, no rust, and the right call on the homes closest to the bay and hills where airborne salt is part of daily life.
- Color and finish: Kynar-based finishes hold color far better than standard paint in UV-heavy California sun. On a Burlingame Tudor cottage, the finish is also a design-review question, not just a cosmetic one.
We carry top-tier material brands across every category we work in, from KraftMaid and Cambria in kitchens to GAF, Owens Corning and CertainTeed on roofs, so the panel and trim you pick come from a manufacturer we stand behind.
What Metal Roofing Costs in Burlingame, CA
Metal roofing in Burlingame lands between $15,000 and $40,000 for a full residential install. That span is wide because five things drive it.
| Line item | Typical range |
|---|---|
| Metal roof installation (full) | $15,000 – $40,000 |
| Tear-off and disposal | Included in install |
| Deck repair / re-sheeting | Quoted separately after inspection |
The variables that push a job toward the top of that range:
- Roof size and pitch. A steep Craftsman roof takes more staging, more safety rigging, and more labor hours per square than a walkable low-slope.
- Existing condition. Old skip sheathing or layered roofing means more tear-off and more deck replacement.
- Panel material. Aluminum and standing seam cost more than exposed-fastener steel; stone-coated sits in between.
- Flashing complexity. Chimneys, dormers, and multiple valleys add labor. Burlingame’s older homes tend to have all three.
- Permit scope. A full replacement with structural repairs carries a larger permit and inspection load than a straightforward re-roof.
Every written estimate is line-itemed, so you see what’s included and what isn’t: tear-off, deck repair, underlayment, flashing, panels, trim, cleanup, and permit filing. Financing is available at 0% for 18 months, and projects over $10,000 get $1,000 off. Pricing is upfront and stays put unless we open the deck and find something the inspection couldn’t see. Call (833) 997-7759 for a free estimate.
See the difference
Before
After
Before
After
Before
AfterWhat Burlingame Homes Specifically Do to This Job
Burlingame is one of the oldest and most architecturally protected suburbs on the Peninsula, and metal roofing here means working with that reality, not around it. In the Burlingame Park and Downtown neighborhoods, and throughout the Easton Addition, the housing stock is dominated by early-1900s through 1940s Craftsman bungalows, Spanish Colonial Revival, and Tudor cottages. Many sit on narrow lots with tight setbacks that make staging and material delivery its own puzzle. Many still have original framing, and a metal roof weighs far less than the tile or heavy shake it might replace, which is often a structural bonus, not a problem.
Historic preservation and design-review scrutiny is real here, and on a roof replacement that usually comes down to finish color and profile. If your home sits in a designated area, the panel color and style may need to match the neighborhood character, so that gets settled before we order a single panel. The climate adds its own demand: Burlingame sits between the bay and the coastal hills, so cool fog-influenced summers and damp winters keep morning moisture lingering on north slopes. That’s why we insist on full synthetic underlayment and layered flashing on every job in Burlingame, wood-sided or stucco. If the metal roof is part of a full Roofing in Burlingame scope, or you’re also weighing Window Replacement in Burlingame while the exterior is opened up, we coordinate the whole thing. You can see the full range of our Roofing work and the other jobs we take on across Burlingame, and homeowners often pair this with Impact Windows & Doors in Burlingame when they’re tightening the whole envelope.
Serving Burlingame, CA – Our Local Coverage Area
We serve Burlingame and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Metal Roofing in Burlingame
A typical Burlingame metal roof takes seven to fourteen working days from tear-off to final inspection, weather permitting. Older homes with deck repair or complex flashing can run two to three weeks. Call (833) 997-7759 for a schedule built around your specific roof.
Yes, a full metal roof replacement requires a building permit in Burlingame, and the finished work gets inspected before sign-off. We handle the permit filing and coordinate the inspection so you’re not chasing paperwork. Call (833) 997-7759 to get started.
We don’t recommend it in Burlingame. Layering a metal roof over old shingles traps moisture and hides deck damage, and on the area’s older homes the deck is exactly what needs to be checked first. A full tear-off costs more up front but protects the investment. Call (833) 997-7759 for an honest assessment.
Metal roofing in Burlingame runs $15,000 to $40,000 installed, depending on roof size, panel material, deck condition, and flashing complexity. Every estimate is line-itemed and priced upfront. Call (833) 997-7759 for an exact quote; estimates are free.
You get the manufacturer’s warranty on the panels and finish, plus our 730-Day Done Right Promise on the workmanship, one of the longest guarantees in residential construction. If something isn’t right, we make it right. Call (833) 997-7759 to talk through the details.
Get a Free Metal Roofing Estimate in Burlingame
If your Burlingame roof is ready for metal, start with a free on-site estimate. Call (833) 997-7759, a live person answers any hour, and we’ll set a time to walk the roof, inspect the deck, and hand you a line-itemed quote with the numbers that matter. Most jobs are completed in a single visit after materials arrive, and every one is backed in writing. From foundation to finish line, we build it to last.
Written by the team at Groundwork Construction Co.