Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in Daly City, CA: What This Job Actually Involves
An iron fence in Daly City typically runs $3500 – $9000 installed, and most residential jobs finish in 2 – 5 working days once materials are on site. The scope covers layout, digging and setting posts in the sandy ground here, setting panels and gates, and final finish work. Call (833) 997-7759 for a free on-site estimate. One thing separates Daly City from the rest of the Peninsula: nearly every lot sits on wind-blown dune sand or a graded hillside cut, so post footings here demand more depth and concrete than a flat-lot job in South San Francisco ever would.
How We Build an Iron Fence Here, Stage by Stage
Iron fencing looks simple from the sidewalk. Underneath, it’s a footing problem before it’s a fence problem, and on Daly City’s slopes that distinction decides whether the fence stands plumb in five years or leans toward the neighbor’s yard.
Stage 1: Site walk and layout (day 1, roughly 2 hours). We walk the property line with you, mark post locations with paint or stakes, and check for buried irrigation, gas lines, and the shallow utility runs common on these postwar lots. You decide the final run of the fence and where gates land. On hillside streets, we also check grade change along the line, because a fence that steps with the slope is set differently than one that runs level.
Stage 2: Digging and footings (days 1 – 2). This is where Daly City earns its reputation. Holes get dug to depth and width sized for the post and wind load, then filled with concrete and left to cure. In dune sand and fill, we often bell the bottom of the hole or add extra concrete to resist pull-out from onshore wind. Curing takes time we don’t skip. Footings set short are the number one cause of leaning iron fence in this city.
Stage 3: Post setting and panel hang (days 2 – 3). Posts go in plumb and braced, then panels and gates get hung and checked for swing, latch alignment, and racking along the slope. You decide gate hardware and whether you want a self-closing hinge or a latch with a lock. If the fence ties into an existing wall or pier, we fit the connection here.
Stage 4: Finish and touch-up (day 4). We touch up welds and scratches, check every fastener, and confirm the finish coat is intact. If you chose a powder-coated product, this step is mostly inspection. If you chose a bare or painted finish, this is where the final coat goes on.
Stage 5: Final walk (day 4 or 5). We walk the line with you, show you gate operation, and leave you with care notes. If your project expands into a full property boundary with landscaping, that’s part of a full Fence Installation in Daly City scope and we’ll quote it in the same visit.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between for an Iron Fence
The word “iron” covers a few different products, and the choice drives both price and how the fence ages in fog-belt conditions. Here’s the honest breakdown:
- Wrought iron (true forged or solid bar): The traditional choice. Heaviest, most durable, and the most expensive. Holds a painted finish well and can be repaired by welding. Suits homeowners who want a fence that outlasts the house.
- Steel or tubular steel: Similar look at a lower weight and cost. Strong and rigid, but the interior can rust if the coating fails. Best with a factory powder coat, which holds up better against Daly City’s persistent marine moisture than field paint.
- Powder-coated finishes: A factory-applied coating that resists chipping and corrosion far better than brushed-on paint. On the foggy west side near Westlake and Serramonte, where surfaces stay damp and get little sun to dry, this is the finish we recommend most often.
- Faux or composite iron-look: Cheaper and lighter, but not real metal and not weldable. Fine for decorative runs, a weaker choice for a security perimeter or a long boundary.
- Gate configuration: A single walk gate, a double drive gate, or both. Gates add cost through hardware, hinges, and the extra framing a wide opening needs. Decide this before footings go in, not after.
What an Iron Fence Costs in Daly City, CA
For a typical residential run, iron fence installation in Daly City runs $3500 – $9000. A short decorative front run lands near the bottom. A long perimeter with a drive gate and hillside footings lands near the top. Here’s what moves that number:
- Linear footage and height: The biggest driver. Height above 4 feet costs more in material and wind load engineering.
- Material grade: True wrought iron costs meaningfully more than tubular steel. Powder coat adds a premium but pays back in finish life.
- Footing conditions: Flat ground is one price. Steep graded hillside cuts and sandy fill, common above the Mission Street corridor, mean deeper holes, more concrete, and more time.
- Gates and hardware: Each gate is a separate line item in the estimate, with hardware priced out. Self-closing and lockable latches cost more than a simple thumb latch.
- Access: A back corner lot with no driveway access to the work line adds labor. Tight side yards in the dense El Camino corridor slow a job down.
Every written estimate itemizes posts, panels, gates, hardware, concrete, and finish, so the number you see is the number you pay. What it doesn’t cover unless stated: haul-away of old fencing, landscape repair after footings, and any permit fee the city charges. If other outdoor work is on your list, homeowners often pair this with Patios, Walkways & Pool Decks in Daly City so the crews coordinate on site access.
See the difference
Before
After
Before
After
Before
AfterWhat Daly City Homes Specifically Do to This Job
Daly City is built almost entirely on wind-blown sand dunes and steep fog-belt slopes on San Bruno Mountain’s western flank. For an iron fence, that means footings here are a soil-engineering question, not a paint-and-post job. We plan for shifting dune sand, active landslide mapping on the steeper streets, and marine moisture that keeps west-facing metal damp for long stretches. The housing stock is mostly 1940s to 1960s stucco-over-wood-frame tract homes on poured slabs set into hillside cuts. When we run a line along a property boundary here, we routinely hit sandy fill and thin lots, and we set posts accordingly. Down in the flat corridors off Mission Street and El Camino, the work is more forgiving; up on the hillside streets, it isn’t. If a project grows into a fence plus a hardscape or an outbuilding, your fence layout should be worked out alongside any ADU Design & Permitting in Daly City, because both share a property line and a drainage plan.
Permitting is worth a call before we dig. Height limits, setbacks, and lot-line placement rules vary by parcel here, and any fence over six feet usually needs a permit. We confirm the requirement with the city during the estimate, not after the holes are dug.
Serving Daly City, CA – Our Local Coverage Area
We serve Daly City and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Iron Fence in Daly City
Most residential jobs take 2 – 5 working days once materials arrive, and the timeline depends on footage, gate count, and how much hillside footing work the site needs. A short flat-lot front run can finish in two days; a long perimeter with a drive gate on a steep lot runs closer to five. Call (833) 997-7759 for a timeline specific to your property.
A permit is usually required for fences over six feet tall, and lot-line placement rules vary by parcel here. We confirm the requirement with the city during the free estimate, so you’re not the one chasing down the answer. Call (833) 997-7759 to schedule that visit.
In most cases, yes. We route the line to avoid irrigation, utility runs, and existing walls, and footings are dug individually rather than trenching the whole run. Where the fence ties into an existing pier or wall, we fit the connection rather than cut into it. Call (833) 997-7759 to walk the line together.
Expect $3500 – $9000 for a typical residential installation, with the low end for a short decorative front run and the high end for a long perimeter with drive gates and hillside footings. Material grade, gates, and site access move the number most. Call (833) 997-7759 for an exact quote, itemized in writing.
All our work is backed by the 730-Day Done Right Promise, a workmanship guarantee of nearly two years. If something isn’t done right, we make it right. We go over the details, including what the manufacturer covers on finishes and hardware, before you sign anything.
Get a Free Iron Fence Estimate in Daly City
We’ll walk your property line, check the grade and soil, and give you an itemized, written quote for your iron fence in Daly City. No pressure, no guesswork. Groundwork Construction Co. covers Daly City and the surrounding Peninsula, and our fence installation service is one of seven core trades we run. Call (833) 997-7759 for a free estimate and design consult. Live person, 24/7.
Written by the team at Groundwork Construction Co.